Features of Guangshengde LED street lamp assembly line:
1. This equipment is dedicated to the detection of aging of AC LED bulbs, 220V, 110V LED energy-saving lamps finished products, through the high-voltage, medium-voltage, normal pressure, low-voltage, high-temperature, roaming, impact and other voltage areas of 220V LED energy-saving lamps Aging, observe whether the LED energy-saving lamp can pass the aging test of the above voltage range. This product is a patented product approved by the Patent Office (Patent No.: ZL 2012 2 0526602.7) 2. The tooling board can aging bulb lamps and LED energy-saving lamps, and can fully meet the product aging time requirements. 3. There are 106 chain plates in the whole line, each of which is equipped with 16 E27 five-magazine lamp holders, 4 pairs of T8 fluorescent lamp holders, 1696 aging bulb lamps or 424 fluorescent tubes (full line)
The technical key points of Guangshengde LED street lamp assembly line:
1. Constant temperature zone: The constant temperature system is completed by electric heating. The lower 5 meters are set as the heating section, and the second meter is equipped with two 1KW ceramic heating tubes, 3 temperature collection points, and the temperature is automatically controlled as: room temperature + 80°C. 2. Detection of the impact beat circuit: a Tianzheng brand voltage regulator 10KW voltage regulator 1 0-250V adjustable, 6 zones are set up across the line, and the impact time of each zone can be set on the touch screen interface. 3. Test the normal voltage circuit: use Tianzheng brand voltage regulator 10KW voltage regulator 1 0-250V adjustable, set as low voltage test area. (The area range is about 7 meters). 4. Detect low-voltage circuit: use Tianzheng brand voltage regulator 10KW voltage regulator 1 0-250V adjustable, set as low-voltage test area. (The area range is about 7 meters). 5. Detection of high-voltage circuit: use Tianzheng brand voltage regulator 10KW voltage regulator 1 0-300V adjustable, set as high-voltage test area. (The area range is about 7 meters). 6. The bulb lamp adopts E27 screw socket. 7. The lamp is used for aging, and it is equipped with a fast T8 lamp holder fixture. (The lamp holder fixture can be adjusted to 300, 600, 900, 1200MM);
Guangshengde LED street lamp assembly line appearance protection requirements:
1. The fuselage and frame are made of 40*40*1.5 (MM) steel pipe welding, the upper and lower parts of the fuselage are made of 130*23 (MM) special aluminum alloy profiles for aging lines, and the guard plate is made of 1.5MM cold plates. 2. The transmission chain adopts inch double-pitch single ear double-hole chain; 3. A light-blocking passport is set on the online body, and the combination of plexiglass and aluminum profile is used to effectively reduce the glare of the energy-saving lamp and better protect the eyes.
Appearance protection requirements of Guangshengde LED street lamp assembly line Dimensions:
1. The whole line is equipped with two electric trough rails, using edge epoxy board. And assembling 3MM thick copper conductive strip. The line body is equipped with a protective anti-drop net to prevent the product from falling and breaking. The high-quality stainless steel fine mesh net is fixed with angle iron on both sides. 2. The equipment must not rust or generate dust. 3. Equipment noise: below 65dB. 4. The feet are equipped with galvanized adjustable level and height adjustable foot cups. 5. The total length of the line body: 10 meters, the height between the working surface and the ground is 750±20mm, adjustable. 6. Dimensions: L10000mm*W1620mm*1270mm
LED street lamp assembly line power and transmission: 1. The motor adopts Taiwan Kun 1.5KW three-phase motor, 1:200 reducer, 2HP frequency converter, frequency conversion speed regulation, linear speed 0-2M/min adjustable, aging time 0-4 Adjustable in hours. 2. It adopts 1 inch T17 tooth double pitch sprocket with φ50 main shaft and tensioning mechanism as the transmission device.